People spend a significant amount of time in workplaces, apartment buildings, schools, care facilities and other frequently occupied buildings. These spaces can also present a risk of long-term radon exposure.
Radon cannot be seen, smelled or tasted. Testing is the only way to know how much radon is present.
Why does radon testing matter?
Radon is a naturally occurring radioactive gas produced by the breakdown of uranium in soil and rock. It can enter buildings through cracks, joints, drains, service penetrations and other openings where the building contacts the ground.
Long-term exposure to radon increases the risk of developing lung cancer. Health Canada recommends taking action to reduce radon levels when the annual average concentration exceeds 200 Bq/m³. [canada.ca]
Why are larger buildings different?
Testing a larger building is not as simple as placing a single detector.
Radon levels can vary throughout a building because different areas may have different foundations, ventilation systems, occupancy patterns and proximity to the ground. A single measurement may not provide enough information to understand conditions across a large or complex facility.
Air pathways within the building can matter as well. Piping and other pathways that allow air to move directly from a basement into other areas of a building may also allow radon to travel.
Testing should begin with a measurement strategy that considers the building as a whole. Health Canada’s guidance for public buildings specifically addresses measurement strategy and measurement locations as part of the testing process. [canada.ca]
Planning radon testing
A good testing plan considers both where people spend their time and how the building is designed and used.
Important considerations include:
Occupied spaces: Focus on offices, classrooms, residential units and other areas where people regularly spend significant amounts of time.
Lowest occupied levels: Give particular attention to occupied spaces closest to the ground. Testing should include every ground-floor and basement space occupied for four or more hours per day.
Upper floors: Testing should include every third occupied room on upper floors.
Building layout: Consider different wings, additions, foundations, floors and sections of the building.
Ventilation and airflow: Heating, ventilation and air-conditioning systems can affect how air moves throughout a building.
Multi-unit buildings: Apartment and condominium buildings require a strategy that considers multiple occupied units rather than assuming one measurement represents the entire property.
Detector locations should be selected carefully and kept away from vents, drafts, exterior doors, direct sunlight, heat sources and areas where the detector could be disturbed.
For larger or more complex facilities, C-NRPP-qualified detector placement services are also available through RPC with the submission of up-to-date floor plans. This is a paid service.
How long should you test?
Radon concentrations can change over time as weather and building conditions change. Long-term testing provides a better indication of average exposure than a short-term measurement. Health Canada similarly recommends long-term measurements for estimating annual radon concentrations in public buildings. [canada.ca].
RPC’s long-term testing guidance uses a minimum testing period of 91 days.
Before testing begins, the appropriate duration, detector locations and number of measurements should be determined based on the building.
What happens after testing?
1. Test
Measure radon concentrations in appropriately selected locations throughout the building.
2. Review
Review the results to understand radon levels in the tested areas and determine whether further investigation is needed.
3. Act
If elevated radon levels are identified, determine the appropriate steps to reduce exposure.
Radon testing is not simply about generating a number. It helps organizations better understand their indoor environments and determine whether action is needed.
Managing multiple buildings?
Organizations responsible for several properties can include radon testing within a broader facility or property-management program.
A planned approach can help identify which buildings and occupied areas should be tested and establish a consistent process across the organization’s property portfolio.
Need help planning your radon testing?
RPC provides radon testing and analysis for commercial and public buildings, including larger-scale and multi-building projects.
Testing is completed through RPC’s in-house analytical laboratory, and RPC is certified through the Canadian National Radon Proficiency Program, or C-NRPP.
For larger or more complex buildings, RPC can also provide C-NRPP-qualified detector placement services using up-to-date building floor plans. This is a paid service.
Whether you are responsible for one facility or multiple properties, RPC can help you determine an appropriate approach to radon testing.
Need help planning your radon testing?
Additional resource
For more detailed technical information, consult Health Canada’s Guide for Radon Measurements in Public Buildings. It includes guidance on measurement duration, testing strategies, detector locations, multi-unit residential buildings, quality control and the interpretation of results. [canada.ca]